It Still Works
You can use either an indoor or outdoor antenna, though the outdoor variety often provides better reception. Place both capacitor controls at their mid-range positions. Best bet, a rooftop antenna, let us know when your ready to make that move.
Your exact connections may be positioned differently, but marked the same. If your house is on a hill, you'll get better reception than if it is in a valley. Route the coaxial cable through the cellar, etc to the radio. Typically your radio already has a very good pre-amplifier built in to its circuitry. Switch the amplifier off, online dating horror stories yahoo and see if the sound improves.
Re-tighten the knobs, replace the tuner cover and you're ready to go. Either one will work fine, though you may need an adaptor, depending on your antenna. If the situation improves, you probably need a better radio. Car radios have to be built to high standards to provide decent reception in a moving vehicle, in the presence of varying terrain, with a serious nearby source of interference your engine!
- Separate the opposite end a few inches, strip the ends and attach to the ohm terminals.
- Easy to find at garage sales.
- They can also be mounted in the attic or the top of a closet if outdoor mounting isn't feasible.
- It doesn't sound like you actually have a dipole with wire just wrapped around a plastic tube.
- Their will be some insertion loss from any transformer.
Most antennas have screw terminals intended for flat, two-strand antenna wire. They are weakened by objects that get between the transmitter and receiver. You will probably notice this type of interference while driving. When that transmit key is down, ring dating someone somewhere can hear you.
From your picture it appears that you have a Ohm flat twin lead attachment from your antenna. However, most of us have, at best, only one of these items. Both types will connect and work in the same way. Somehow, secure the pipe to the roof or side of your house remember the higher the better! Now everybody uses round coaxial cable.
Loosen the screws on the outdoor antenna's terminals, attach the antenna wire or coaxial adaptor and re-tighten the screws. Right now I just have a piece of speaker wire stuck to the back of my receiver and it helped reception, but it still sucks. In other words, very slowing tune it to get the stereo light to work. You may find that you have to vary the position of the inductance switch a position or two either way to get your best match. You can buy cheap adapters to convert either one to the other depending on your needs.
Measure the distance from your antenna to your radio or your stereo receiver, leaving some additional length for routing the wire around obstacles. All of a sudden, Howard Stern will override your Morning Edition! Adjust the tuning to get the meter centered.
Kenwood and Pioneer are at fault. If the stereo won't work, it could mean their tuners need realigned. Remember that you have to have an external amplifier and speakers for this one! You can get the same reception in a bad location using a great antenna as you can in a good location using a bad antenna!
This is a decent choice if you like to station-hop. When noise peaks out using your ears and the S meter, your tuner settings should be very close for final operation. So if you listen to several stations broadcasting from different directions this might not be ideal. Try connecting a better antenna see below and see how your reception improves! If not, loosen their Allen screws and rotate the knobs so that they point to mid scale.
Welcome Summer Friends
Connect the antenna wire to the antenna terminals on your stereo. Select your final band of operation and repeat the procedure above. Boston Acoustics Horizon Solo. Flat ohm antenna wire attaches directly to screw terminals, and round coaxial cable attaches directly to a cable-style F-connector. Let me know how they work for you.
How to connect 75 ohm antenna to single wire antenna FM tuner
Connect the spade lugs to the ohm terminals on your receiver or tuner, and screw your incoming cable to the other end of the transformer. Don't trust the knob markers if this is your first experience with the tuner! The transmitter now can produce it's rated power out to the tuner in the hopes that the tuner can do it's job and get most of that power into the antenna system with some efficiency. If you're in a decent area it should help but don't be surprised if you need more of an antenna to get some decent performance. Purchase a length of antenna wire that reaches this distance.
If you are settled on speaker wire not the best pick hook one end to the common, the other to Ohm. Get a better antenna or a better location for it. Brought to you by Techwalla. Or if you happen to repeatedly see the same vehicle producing the same interference to your radio, you might ask the owner to switch the output frequency of his device. If the knobs are pointing to half scale with the reference markings on the knobs and front cover, consider yourself lucky.
So can someone take a snap shot of the back of their receiver or just carefully explain it to me? It's not my tuner, I found the pic online but, look for those screws. In layman's terms, all a tuner does is act as a kind of adjustable impedance transformer between the radio and the antenna. But lets work on improving both! In other words, if your radio has a built-in antenna, it will work better in your attic, than in your basement!
Even a dummy load gets out somewhere! This article was written by the It Still Works team, copy edited and fact checked through a multi-point auditing system, application.screenupdating in efforts to ensure our readers only receive the best information. You can get tripod roof mounts and wall mounts from Radio Shack as well as antenna mast.
Installing an outdoor antenna can be fun, challenging, or both! Note that the rf is actually flowing in both directions and not just toward the antenna. So re-check and re-tune as needed as you move around the band.
Best ways to hook up an fm antenna onto a stereo receiver
If you drill a hole, weatherproof it with caulking. Older televisions might have a pair of screw terminals, but most have the threaded cable-type F-connector. If your equipment has cable-type connectors, use a standard cable splitter and buy adaptors to convert your twin-lead wire to coaxial. In the mean time, when tuning a strong station try sneaking up to it.
Not easy for a non-professional to do. Also, if improperly installed, some of these devices can cause tremendous areas of interference! Hit the Yellow Pages or ask around.
Video of the Day
You'll be surprised at how well this works! Technically there are several things wrong with this approach. To cure this, try to either use a directional antenna, or try to re-orient your antenna to maximize your reception.
So, waddaya got back there? This radio is located in your automobile. If you're using flat-lead wire, use an adaptor to convert it to coaxial cable and use a standard cable splitter. You would connect one side of the lead to one terminal and the other side to the other.
- You simply screw the antenna lead into this.
- In the photograph the stereo and power indicators appear to be illuminated.
- If you'd rather use shielded coaxial cable, purchase an adaptor at an electronics store.
- Try to determine which of these sources is causing the problem and isolate it.
- Boston Acoustics Horizon Duo.
Or perhaps a couple of screw terminals? This is partially because your car radio is probably better than your home radio. Feed the wire into your house through a vent, for arguments the soffits or a newly-drilled hole in your wall.